Addonics Technologies Computer Hardware CPR5SA User Manual

T E C H N O L O G I E S  
User Guide  
Compact RAID  
(CPR5SA)  
v5.1.11  
Technical Support  
If you need any assistance to get your unit functioning properly, please have your  
product information ready and contact Addonics Technical Support at:  
Hours: 8:30 am - 6:00 pm PST  
Phone: 408-453-6212  
 
Power Switch / Buzzer Disable Button  
Reset Device / Change Mode Button  
RAID Setting Dip Switch  
eSATA Connection  
Power Connector  
Installation Guide  
1. To open the front panel,  
press the push-open button.  
2. Slide the 2.5” SATA hard  
drive into the slot. Push back  
the front panel.  
Two Options for Setting RAID on the Compact RAID Box  
(only select one option)  
I.  
Using the JMicron HW RAID Manager utility program  
For Windows users, install the JMicron HW RAID Manager located on the  
SATA Controller CD. In the CD, go to RAID utilities > JMB393. This  
manager can be used to create and monitor the status of the RAID volume.  
Use the RESERVE DIP switch setting when using the JMicron HW  
RAID Manager.  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  
II.  
Using the onboard RAID DIP switch  
RAID Status  
DIP Switch  
1
2
3
RAID 0 (stripped)  
RAID 10  
JBOD (Large)  
RAID 3  
Clone  
RAID 5  
ON  
ON  
ON  
ON  
OFF  
OFF  
OFF  
OFF  
ON  
ON  
OFF  
OFF  
ON  
ON  
ON  
OFF  
ON  
OFF  
ON  
OFF  
ON  
RESERVED  
Normal (Individual drives)  
OFF  
OFF  
OFF  
a.  
b.  
Select the setting desired using the DIP switch table.  
Using the provided eSATA to eSATA cable, connect one end to the  
eSATA port on the RAID box and the other end to the eSATA  
controller card.  
c.  
d.  
e.  
Press the power switch button for more than 2 seconds. Wait for  
power LED status to change from starting to ready.  
Press the “Change mode” button for more than 2 seconds. This will  
configure the raid volume.  
Navigate to the Disk Management utility to configure the drives.  
Note: for the system to detect multiple individual drives, the RAID box must be  
connected to a port multiplier compatible eSATA host controller. If the RAID box is  
NOT connected to a port multiplier compatible eSATA host controller, the system will  
only detect one drive and that is the hard drive in slot HD0.  
RAID Monitoring LED  
RAID Status  
LED Indicator  
Access  
RAID 10  
Blue / Flash  
Rebuilding  
Access  
Blue & Red / Flash  
Blue / Flash  
RAID 3  
RAID 5  
Clone  
Rebuilding  
Access  
Blue & Red / Flash  
Blue / Flash  
Rebuilding  
Access  
Blue & Red / Flash  
Blue / Flash  
Clone  
Blue & Red / Flash  
Blue / Flash  
JBOD (Large)  
RAID 0  
Access  
Access  
Blue / Flash  
 
Technical Support (M-F 8:30am - 6:00pm PST)  
Phone: 408-453-6212  

321 Studiosr QW2S User Manual
Aastra Telecom IP Phone IP User Manual
Acer Computer Monitor S243HL User Manual
Adcom Stereo Amplifier GTP 760 User Manual
Airlink101 Computer Drive ANAS550 User Manual
Amana Refrigerator AFI2538AEW User Manual
American Audio CD Player DCD PRO300 User Manual
Audiovox Car Stereo System CD 3610 User Manual
Avet Reels Fishing Equipment LX 80 User Manual
Baldor Riding Toy mn722 User Manual